(1) Glue compounding on the composite board: check whether the panel and bottom plate of the composite board production line are dry, and pick out the board with moisture. (1) ترکیب چسب روی صفحه کامپوزیت: بررسی کنید که پانل و صفحه پایین خط تولید تخته کامپوزیت خشک است ، و تخته را با رطوبت انتخاب کنید. Adjust the glue, adjust the glue and calcium carbonate evenly, and adjust the toner to the same color as the panel. چسب را تنظیم کنید ، چسب و کربنات کلسیم را به طور مساوی تنظیم کنید و تونر را به همان رنگ پانل تنظیم کنید. According to the climate and humidity at the time, add an appropriate amount of curing agent, the ratio of curing agent to glue is 1 ~ 3%. با توجه به آب و هوا و رطوبت موجود در آن زمان ، مقدار مناسبی از ماده پخت کننده را اضافه کنید ، نسبت ماده ترمیم کننده به چسب 3 1 1 است.
(2) Pre-composite process of panel: if faced with a polished surface and a mesh panel, it must be carefully selected and sent to a hand-held grinder for de-glazing. (2) فرآیند از پیش کامپوزیت پانل: در صورت مواجه شدن با سطح صیقلی و توری مش ، باید آن را به دقت انتخاب کرده و برای لعاب زدایی به یک چرخ دستی دستی ارسال کنید. It is de-aired according to the flatness, dry-grinded and leveled, but not deep-grinded; مطابق صاف بودن ، خشک شدن و تراز بودن ، اما عمیق و خرد نشده از بین می رود. then the net is broken off Cloth shovel flat surface glue. سپس توری از چسب سطح صاف و بیل پارچه شکسته شده است. If the shovel cannot be removed, you should use a hand-held grinder to grind off the net surface glue. اگر بیل را نمی توان از بین برد ، باید از چرخ دستی استفاده کنید تا چسب سطح خالص را خرد کنید. Use double-sided smoothing to remove dust from the dry-milled panel. برای از بین بردن گرد و غبار از پانل خشک شده از صاف کردن دو طرفه استفاده کنید.
(3) The pre-composite process of the bottom plate: the bottom plate with light should be de-glazed and then thickened, usually the thickness of 20mm bottom plate should be 17mm. (3) فرایند پیش کامپوزیت صفحه پایین: صفحه پایین با نور باید از لعاب و سپس ضخیم شود ، معمولاً ضخامت صفحه پایین 20 میلی متر باید 17 میلی متر باشد. After the bottom plate is fixed, remove moisture. بعد از ثابت شدن صفحه پایین ، رطوبت را بردارید. Can be pulled outside to dry, dry or blow dry. می توان آنرا بیرون کشید تا خشک شود ، خشک شود یا خشک شود. Note that if the board is not dry, it cannot be glued to avoid delamination or infirmity. توجه داشته باشید که اگر تخته خشک نیست ، نمی توان برای جلوگیری از لایه لایه شدن یا ضعف ، چسب زد.
(4) Select panel: select the marble panel that meets the customer's requirements. (4) پانل را انتخاب کنید: پانل مرمر را انتخاب کنید که پاسخگوی نیاز مشتری باشد. Clarify the types of materials and the consistency of colors. انواع مواد و قوام رنگ ها را روشن کنید. Note that when selecting the panel, it should be free of scars, warpage, trachoma, depressions, stains, etc. If the wool board does not show the effect, the panel can only be determined after spraying the board with a water gun. توجه داشته باشید که در هنگام انتخاب تابلو ، باید عاری از زخم ، صفحه جنگی ، تراکومو ، افسردگی ، لکه و غیره باشد. اگر تخته پشم جلوه ای از خود نشان نداد ، پانل فقط پس از پاشیدن تخته با اسلحه آب قابل تعیین است.
تماس با شخص: Mr. Arno Hao
تلفن: +8618717894416